Setting up a VT1000 vibratome
Setting up a Faulhaber motor controller with a Leica VT1000
The Leica VT1000 vibratome head works well and requires just a DC motor controller. The motor and encoder in a VT1000 are made by Faulhaber so if you buy a Faulhaber motor controller it is easy to run the unit at a defined RPM. The motor is a Faulhaber 3540K012C (datasheet) connected to a HEDS-5500 encoder (datasheet). The following instructions are written assuming you are using a Faulhaber MCDC 3006 S RS controller. These are no longer made (but are available on eBay) and the new model (MC5005 S RS) is NOT a drop-in replacement because it does not have a reasonable serial interface any more. We are looking for a suitable replacement device.
It is a good idea to connect the encoder, since you have it and you will get better control of motor speed this way.
Connecting the controller
Hook up the motor to a 12V DC 1 A supply.

Snip off the green connector coming off the motor on the vibratome, strip the leads, and tin the bare wires.

Hook up to the controller as shown below. Note the far right motor +/- leads power the motor; here these wires look thicker for those cables as the originals were extended. The thinner black and red wires are power for the encoder. The encoder sensor wires are the remaining two: white and brown.

Finish off the install by hooking up the serial cable to the PC (with the MC5005 S RS you can use a USB cable). Power on the device!
Connect to the controller
The following instructions are for Faulhaber Motion Manager 6, which you should install now. Note it is possible your version of Motion Manager 6 won't look exactly like what is shown below, but it should be close enough.
Click "Establish Connection" in the top left. Select the COM port of your device then "Next". Then select the first entry in the drop-down ("Motion Control V2.x") and select "Next", then "Next" through the next window.
You will then see a window that lists your controller:
Click "Finished" and the main window will now look like this:
Set the drive parameters
Press "Select motor" under the "Establish connection" button. You will need to make a motor with the right properties. Press "Create" in the following window:
Now fill in the next window as follows:
Press "Next" and in the next window you will enter the properties of the motor. You might find that your window looks different to the following. In which case use the 3540K012C datasheet to find the correct values. Remember that in this datasheet 1,7 means 1.7.
Now "Save". Confirm the settings on the original page look as follows. The encoder is a HEDS-5500-A which has a spec sheet that says it has 500 lines/rev. So set the pulses per rev to 500 pulses/rev. Correct that if needed and hit "Next"
Skip the next window describing the gear train ("Load transmission"). Just "Next" through it.
In the following window ("Factor of inertia"), J_Load should be "20".
In the next window, just press 'Next' to select the default "quiet running".
"Finished" on the summary page. This sends the parameters to the motor and you should say "Yes" when offered to store these to the device.
You can test the device by going to the "Operate motor" section and running the motor at 3200 RPM, which is the default speed in BakingTray.
The motor should run almost silently with the blade holder and blade attached, assuming everything is bolted down tightly. Quit the software.
Confirming the vibratome can communicate with BakingTray
You should have already added BakingTray to your path. The following sample session shows how to start up the class for controlling the vibratome and sending commands to it.
If you have run through all of the steps, ensure that the controller is in the correct mode for running with the encoder:
You do not need to run that again: the mode has been stored in the controller's non-volatile memory.
You can now control the motor in RPM:
Running without the encoder
If you could not set the motor up with the encoder using the above steps then follow this section. Perform the following steps with the vibratome securely mounted, blade in blade holder, and blade holder mounted. Nothing should be loose. Do not excessively tighten things, though, this is not needed.
The following sample session shows how to start up the class for controlling the vibratome and sending commands to it.
You now need to tell the controller to run without the encoder:
You do not need to run that again: the mode has been stored in the controller's non-volatile memory.
You should consider the sample speed setting, which is the input argument to startVibrate, to be in arbitrary units. The goal now is to identify a reasonable speed setting for slicing the sample.
If you run the vibratome too fast you will wear out the axle or the bearings and may need to replace the whole unit after a year or two. Make a note of the vibrate speed chosen above. You will later use this when making the BakingTray settings file and only modify it if you notice cutting problems.
Last updated